• Netmail

    From Rick Smith@1:340/202 to All on Sun Apr 19 18:31:00 2020
    Greetings,

    Do I have to setup anything special for a .point to get netmail? My point can communicate with mystic both directions and have sent netmail out to other systems from point, but do not receive the replies?

    ---
    |02Regards,

    |09Rick|03 //|04 Nitro

    --- Mystic BBS v1.12 A46 2020/04/09 (Windows/64)
    * Origin: Abacus BBS (1:340/202)
  • From Al@1:153/757 to Rick Smith on Sun Apr 19 19:22:30 2020
    Hello Rick,

    Do I have to setup anything special for a .point to get netmail? My
    point can communicate with mystic both directions and have sent
    netmail out to other systems from point, but do not receive the
    replies?

    The BOSS should send netmail addressed to the point without any further ado. It's also possible others that know the connection details can send directly to
    your point but in most cases the boss will need to route netmail to the point.

    Ttyl :-),
    Al

    --- GoldED+/LNX
    * Origin: The Rusty MailBox - Penticton, BC Canada (1:153/757)
  • From Dan Richter@1:317/3 to Rick Smith on Sun Apr 19 20:43:40 2020
    On 19 Apr 2020, Rick Smith said the following...

    Do I have to setup anything special for a .point to get netmail? My
    point can communicate with mystic both directions and have sent netmail out to other systems from point, but do not receive the replies?

    In the node settings for your point address, make sure you add the routing info. Eg:
    Route Info: 1:340/202.1

    Also, from the point system, you would want to route everything to the hub. This can be done with:
    Route Info: 1:* 2:* 3:* 4:*

    Hope this helps.


    ---

    Black Panther(RCS)
    Castle Rock BBS

    --- Mystic BBS v1.12 A45 2020/02/18 (Linux/64)
    * Origin: Castle Rock BBS - bbs.castlerockbbs.com (1:317/3)
  • From Rick Smith@1:340/202.1 to Dan Richter on Sun Apr 19 20:50:18 2020
    Greetings Dan!

    19 Apr 20 20:43, you wrote to me about an urgent matter!:


    In the node settings for your point address, make sure you add the
    routing info. Eg: Route Info: 1:340/202.1

    Thank you I am testing that now..

    Also, from the point system, you would want to route everything to the hub. This can be done with: Route Info: 1:* 2:* 3:* 4:*

    Yeah it seems my netmail goes out just fine, its the receiving that is not working.
    -+-
    Regards,

    Rick Smith (Nitro)

    ... A job is nice, but it interferes with my BBSing...
    --- GoldED+/LNX 1.1.5--b20170303
    * Origin: ----> Abacus Sysop Point (1:340/202.1)
  • From IB Joe@1:342/200 to All on Thu Mar 3 12:54:30 2022
    I have been playing a little with the BBS setup. I have decided to try and get my netmail up and running.

    I have the route statement setup to send my NC my netmait... my routing setup for my NC says 1:* 2:*... and so on.... From what I know is this... If there is a netmail for Zones 1 & 2 they'll get routed my NC.

    I think I understand that I can prioritize things... If there are systems hooked up to me I can direct their netmail to them directly as long as I put them before my NC so as it is dealt with before the global routing command kicks in...

    I have posted several netmails and nothing seems to leave my system. Netmail says sent but nothing seems to be sent out..

    Ooooooh... I run "mis poll route" after leaving messages

    Thanx

    IB Joe
    AKA Joe Schweier
    SysOp of Joe's BBS
    -=JoesBBS.com=-

    ... Reward for a job well done: More work

    --- Mystic BBS v1.12 A48 2022/02/09 (Windows/64)
    * Origin: JoesBBS.Com, Telnet:2323 SSH:2222 HTTP:80 (1:342/200)
  • From g00r00@1:129/215 to IB Joe on Thu Mar 3 16:23:22 2022
    I think I understand that I can prioritize things... If there are systems hooked up to me I can direct their netmail to them directly as long as I put them before my NC so as it is dealt with before the global routing command kicks in...

    What you mentioned sounds right. If you want zone 1 and 2 to go to a certain node then you would set your route to 1:* and 2:* as you have done.

    With the latest A48 though most people won't need to set any values for the route because Mystic does all the routing automatically. Setting up echomail in the latest A48 is as simple as this:

    1. Get details from your network hub and create their entry in Echomail Nodes 2. Enter your network address into Network addresses
    3. Enable all the events prefixed with [FTN] in the event editor.

    Mystic does everything else for you automatically, no other setup required it will auto create the bases, send/receive mail as needed, etc! :)

    You can optionally add a "step 4" which would be to go into your Server settings and enable the "BINKP Server" so that you have a mailer running full time too.

    Ooooooh... I run "mis poll route" after leaving messages

    "mis poll route" isn't something you would want to run automatically, just in case that is what you are doing. There are some tossers I think that use some sort of "route" command but that is not what this is.

    This is just for testing your routing setup. You can type "mis poll route <address>" and Mystic will print out were it will send netmails that are addressed to <address>. For example:

    C:\mystic>mis poll route 1:1/1

    Netmail addressed to 1:1/1 would route to 1:154/10 (FidoNet HUB: Pharcyde)

    ... Kids: They're not sleeping, they're recharging!

    --- Mystic BBS v1.12 A48 2022/03/02 (Windows/64)
    * Origin: Sector 7 * Mystic WHQ (1:129/215)